M_G Posted April 18, 2016 Share Posted April 18, 2016 Just found the new 3.922: https://github.com/keyboardpartner/HX3/tree/master/LATEST Some fixes, use with care... ;-)) Changelog 04/18/2016 Firmware #3.922, FPGA 11042016, ScanCores #23 Fixed bug in "Button Vibrato" version (Drawbar Expander), vibrato LEDs did not change on presets Fixed "MIDI Volume" bug in Drawbar Expander, master volume did not change on MIDI CC (although displayed) Fixed "weaker lower manual volume" bug Separate TONE and AMP potentiometer enables "Latching Presets" firmware will now mute on CANCEL key, i.e. jump to preset 11 Deeper bass pedal sound if pedal sustain off Slightly changed AO28 equalizing for more "bottom" and lower mids Slightly more generator output for full distortion on simulated rotary amp Wider swell pedal range Fixed "Note 25" bug on pedal scan routines MIDI Sustain by CC #64 introduced on all scan cores Quote Studio: Hammond XK5-XLK5, Roland Fantom 8, Prophet 5, Roland SE02, Neo Vent, HX3-Expander, Yamaha Montage M7 Live: Yamaha CP88, Hammond SKX Pro, Hammond XB2-HX3, Roland Fantom 07, Roland SA1000, Neo Vent Link to comment Share on other sites More sharing options...
TKN Posted April 18, 2016 Author Share Posted April 18, 2016 I'm updated, and ready to try! :-) Quote Link to comment Share on other sites More sharing options...
TKN Posted April 18, 2016 Author Share Posted April 18, 2016 It´s even better now after this update! Quote Link to comment Share on other sites More sharing options...
hardware Posted April 18, 2016 Share Posted April 18, 2016 Coolness..... Quote Magnus C350 + FMR RNP + Realistic Unisphere Mic Link to comment Share on other sites More sharing options...
analogholic Posted April 19, 2016 Share Posted April 19, 2016 Updated to 3.92 the other day. When I downloaded the 3.922 file, I noticed that it's way smaller only 32k compared to the 3.92 which is 1.5mb?!? Can't even open it. Obviously I'm doing something wrong here. Also, tried to create a custom midi cc map to use with my NE3 with the remote editor. Mapped the parameters, sent it to the HX3, and nothing. The only parameter it's receiving from the Nord is CC 7, which it did before as well. Quote All truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident. Arthur Schopenhauer Link to comment Share on other sites More sharing options...
M_G Posted April 19, 2016 Share Posted April 19, 2016 Downloaded the file (3.922 - Flash for Expandermk3-4) again with another PC. It shows 1,59 MB I guess something went wrong with your download.... Quote Studio: Hammond XK5-XLK5, Roland Fantom 8, Prophet 5, Roland SE02, Neo Vent, HX3-Expander, Yamaha Montage M7 Live: Yamaha CP88, Hammond SKX Pro, Hammond XB2-HX3, Roland Fantom 07, Roland SA1000, Neo Vent Link to comment Share on other sites More sharing options...
Bronks Posted April 19, 2016 Share Posted April 19, 2016 I had my HX3 a week ago. 3.92 was already in out of the box. Supercool. Quote Don't take me serious, I'm just playing. ------------------------------------------------------------ Gear: Hammond XK5-system, Nord Stage3 Compact, Crumar Seven, Rhodes Mk2; Hammond M44 Link to comment Share on other sites More sharing options...
kenheeter Posted April 19, 2016 Share Posted April 19, 2016 Hi everyone, I just pre-ordered a GSI Gemini module and now I'm going to sell my pristine HX3 if anyone's interested. I'm in Canada so that may be a consideration. I just updated it to 3.92 and it sounds great! Cheers, Ken Quote Link to comment Share on other sites More sharing options...
analogholic Posted April 19, 2016 Share Posted April 19, 2016 Ok, succeeded downloading 3.922. Tried to update to 3.922 (using flash) and something went wrong. (3.92 went fine) Now I have invalid licences for both organ and Leslie and no sound at all. What to do? Tried to do a restore, but same thing. Quote All truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident. Arthur Schopenhauer Link to comment Share on other sites More sharing options...
M_G Posted April 19, 2016 Share Posted April 19, 2016 Not sure, but the license numbers are on your invoice.... If not contact: info@keyboardpartner.de Carsten or Christian will help,you out! Quote Studio: Hammond XK5-XLK5, Roland Fantom 8, Prophet 5, Roland SE02, Neo Vent, HX3-Expander, Yamaha Montage M7 Live: Yamaha CP88, Hammond SKX Pro, Hammond XB2-HX3, Roland Fantom 07, Roland SA1000, Neo Vent Link to comment Share on other sites More sharing options...
analogholic Posted April 19, 2016 Share Posted April 19, 2016 Thanks man! Quote All truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident. Arthur Schopenhauer Link to comment Share on other sites More sharing options...
TomKittel Posted April 21, 2016 Share Posted April 21, 2016 Yesterday I updated my HX3 from 3.92 to 3.922 using the remote software. I thought it's just a minor update because of the slightly different version number. But this update is awesome. Much better bass response now. Kudos to the developper! HX3 is getting better and better. I am a fanboy. Quote LIFE IS SHORT, GO GET THE GEAR YOU WANT ;-) Link to comment Share on other sites More sharing options...
hardware Posted April 21, 2016 Share Posted April 21, 2016 I stop because I see this now since I screwed things up and had Diversi fix it and return it to me within a week. Sterling Service indeed. But this stops me in my tracks everytime. I have everything I need, can scuplt the sound in real time while performing, unlike Native where zippers and artifacts ruin parameter modulations. FPGA and DSP don't suffer from bloated Apple or Microsoft one size fits all gunk. I will wait for an upgrade where lower manual gets it's own output, and upper manual can be better isolated. Until then I love my 70s multiple B3 Emulations. http://s31.postimg.org/hdsc86igr/hx3_flash.jpg free adult image hosting Quote Magnus C350 + FMR RNP + Realistic Unisphere Mic Link to comment Share on other sites More sharing options...
Doerfler Posted April 21, 2016 Share Posted April 21, 2016 I stop because I see this now since I screwed things up and had Diversi fix it and return it to me within a week. Sterling Service indeed. I hear you Haywood. I had no problem updating to 3.92, waiting a minute to go to 3.922 however. Just because. Quote Link to comment Share on other sites More sharing options...
DaBous Posted April 22, 2016 Share Posted April 22, 2016 Ok, succeeded downloading 3.922. Tried to update to 3.922 (using flash) and something went wrong. (3.92 went fine) Now I have invalid licences for both organ and Leslie and no sound at all. What to do? Tried to do a restore, but same thing. I just had the same issue. Did you ever get a reponse? Quote Link to comment Share on other sites More sharing options...
Doerfler Posted April 22, 2016 Share Posted April 22, 2016 from what I have read on this thread seems like no problem updating to 3.922 using the remote software but using flash install is causing problems with some end users. Any more thoughts? Quote Link to comment Share on other sites More sharing options...
DaBous Posted April 22, 2016 Share Posted April 22, 2016 Ok, succeeded downloading 3.922. Tried to update to 3.922 (using flash) and something went wrong. (3.92 went fine) Now I have invalid licences for both organ and Leslie and no sound at all. What to do? Tried to do a restore, but same thing. I just had the same issue. Did you ever get a reponse? Quick update I was able to use the remote software to update the FPGA and FW software to the latest versions. Also resent the licenses using the advanced tab on the remote software. Be careful of the flash updater....... Quote Link to comment Share on other sites More sharing options...
KBPChristian Posted April 23, 2016 Share Posted April 23, 2016 Here is a message from Carsten posted in the HX3 Forum concerning update issues: 'Windows allows start of applications directly in explorer ZIP windows. This procedure will run into problems as HX3 Flash and HX3 Remote expect additional files to be present. IMPORTANT: Be sure to extract all files to a local hard disk folder before running HX3 applications. Update will fail if started directly from ZIP window. If the update has failed, you should re-install firmware and licences with HX3 Remote for a complete parameter reset. Download ZIP file and extract contents to a lokal harddisk folder. Start HX3 Remote and connect to USB device. HX3 Remote will show your board info. Uncheck all "Auto Restore" boxes. Install HX3 firmware by clicking "Update FW" and open file appropriate to your device. Old boards prior to 2015 will need "mk2" versions. Install new FPGA configuration by clicking "Update FPGA" and open file "fpga_11042016.bit". Click on tab "Advanced" and enter organ/rotary licence numbers in "Create/send new HX3 board Licences" fields if "Board Info" does not show valid licences. Then click "Send Licences" and finally "Finalize". A new HX3 Flash version is online from April 23rd, 2016. Please only use this version. It will create two text files "hx3_board_info.txt" containing your current licence info and a log file named "hx3_update_log.txt". In case of emergency, please attach these files to email requests. We can create new licenes for you at no cost when we know your serial number.' Regards Christian KeyboardPartner Quote Link to comment Share on other sites More sharing options...
JohnDoe Posted April 23, 2016 Share Posted April 23, 2016 A step by step update video on YT would sure be a great help! Quote "This is my rig, and if you don´t like it....well, I have others!" "Think positive...there's always something to complain about!" Link to comment Share on other sites More sharing options...
ShadowMan Posted April 23, 2016 Share Posted April 23, 2016 While I love the sound of the HX3 and its drawbar controller, I'm just not enjoying the functionality with my Nords as controllers - so I'm going back to my old Electro rig with Ocean Beach drawbars. Module and controller are now up for sale in classifieds. Quote Link to comment Share on other sites More sharing options...
DaBous Posted April 23, 2016 Share Posted April 23, 2016 Here is a message from Carsten posted in the HX3 Forum concerning update issues: 'Windows allows start of applications directly in explorer ZIP windows. This procedure will run into problems as HX3 Flash and HX3 Remote expect additional files to be present. IMPORTANT: Be sure to extract all files to a local hard disk folder before running HX3 applications. Update will fail if started directly from ZIP window. If the update has failed, you should re-install firmware and licences with HX3 Remote for a complete parameter reset. Download ZIP file and extract contents to a lokal harddisk folder. Start HX3 Remote and connect to USB device. HX3 Remote will show your board info. Uncheck all "Auto Restore" boxes. Install HX3 firmware by clicking "Update FW" and open file appropriate to your device. Old boards prior to 2015 will need "mk2" versions. Install new FPGA configuration by clicking "Update FPGA" and open file "fpga_11042016.bit". Click on tab "Advanced" and enter organ/rotary licence numbers in "Create/send new HX3 board Licences" fields if "Board Info" does not show valid licences. Then click "Send Licences" and finally "Finalize". A new HX3 Flash version is online from April 23rd, 2016. Please only use this version. It will create two text files "hx3_board_info.txt" containing your current licence info and a log file named "hx3_update_log.txt". In case of emergency, please attach these files to email requests. We can create new licenes for you at no cost when we know your serial number.' Regards Christian KeyboardPartner Although I am sure the problem described here is an issue. This was not the problem I had. The issue I experienced with the flash was after the first part of the update completed, the USB connection timed out and left the update partially done and the licenses invalid. With the latest package for the remote ( available now diversi.us ) I was able to complete the update and resend the licenses using the remote software. Not going to attempt the flash again. It is important to get the latest version of the ALL package. Quote Link to comment Share on other sites More sharing options...
DiversiOrgan Posted April 29, 2016 Share Posted April 29, 2016 Here is a message from Carsten posted in the HX3 Forum concerning update issues: 'Windows allows start of applications directly in explorer ZIP windows. This procedure will run into problems as HX3 Flash and HX3 Remote expect additional files to be present. IMPORTANT: Be sure to extract all files to a local hard disk folder before running HX3 applications. Update will fail if started directly from ZIP window. If the update has failed, you should re-install firmware and licences with HX3 Remote for a complete parameter reset. Download ZIP file and extract contents to a lokal harddisk folder. Start HX3 Remote and connect to USB device. HX3 Remote will show your board info. Uncheck all "Auto Restore" boxes. Install HX3 firmware by clicking "Update FW" and open file appropriate to your device. Old boards prior to 2015 will need "mk2" versions. Install new FPGA configuration by clicking "Update FPGA" and open file "fpga_11042016.bit". Click on tab "Advanced" and enter organ/rotary licence numbers in "Create/send new HX3 board Licences" fields if "Board Info" does not show valid licences. Then click "Send Licences" and finally "Finalize". A new HX3 Flash version is online from April 23rd, 2016. Please only use this version. It will create two text files "hx3_board_info.txt" containing your current licence info and a log file named "hx3_update_log.txt". In case of emergency, please attach these files to email requests. We can create new licenes for you at no cost when we know your serial number.' Regards Christian KeyboardPartner Although I am sure the problem described here is an issue. This was not the problem I had. The issue I experienced with the flash was after the first part of the update completed, the USB connection timed out and left the update partially done and the licenses invalid. With the latest package for the remote ( available now diversi.us ) I was able to complete the update and resend the licenses using the remote software. Not going to attempt the flash again. It is important to get the latest version of the ALL package. You don't need to get the ALL package. Just what you need for your unit. HX3 Mrk2 (older unit), HX3 Mrk3/4 (current) or the DB-e (Drawbar Expander). However, there are some people that have both the Module and the Drawbar Expander so rather then download two files they grab the ALL zipped package. One other note. There is now 3.924. There was a bug in the Expander version that prevented the Percussion, A/B and Split buttons from sending the control information to the turn on or off these functions as well as a couple of minor things. Carsten updated everything. As to unpacking the Zipped package. I also suggest that you either Move, Rename or Delete the Subdirectory of your older version before unzipping and using the newest version. I still find that Windows sometimes picks up the old folders of the previous release. This isn't unique to the HX3 software as I have it happen with other Windows programs. Regards, Tom Tuson Quote Link to comment Share on other sites More sharing options...
DiversiOrgan Posted April 29, 2016 Share Posted April 29, 2016 Note to ALL owners of KeyboardPartner products in the US and Canada. Please! No mater if you purchased your unit direct from Germany or anywhere else in the US or Canada please go to the Diversi website and register your unit(s) with us or use the following link. https://form.jotform.com/51235176260146 If you have or are buying a used unit from someone please register with us as we have a small email list that we send out informing owners about current updates and anything that needs to be passed on to you the owners. In addition, if you purchased the unit used we want to cover you by moving the Software Licenses over, to you, from the old owner. This way if you ever need to obtain the Licenses, do to some problem, we have them on file here and can get them to you. Also, we never share your information with anyone other them KeyboardPartners, if needed. This email list is for you the HX3 owners as a service. OH! There is one other reason. You get advanced notice of anything special or events. One more item. For HX3 owners here in the US and Canada. I can provided a Live Remote Desktop session with you via LogMe.In. It's FREE! However, you have to contact me so we can setup a day and time that is convenient for both of us. I thank everyone for their time. Regards, Tom Tuson Diversi Quote Link to comment Share on other sites More sharing options...
Bill R Adams Posted May 18, 2016 Share Posted May 18, 2016 Anyone using a NIB4D to control HX3? I am finding that everything is working great except C/V. All I can get is vibrato which I would never use. When I switch the controller to chorus the HX3 still has vibrato. Kinda frustrating. Quote "You better get outta town before your nickname expires" WZ Link to comment Share on other sites More sharing options...
bluzeplayr Posted May 18, 2016 Share Posted May 18, 2016 Yes, I had the same problem trying to upgrade the sound of my Nord Electro 73 with a HX3-DE (the module that includes 2 sets of drawbars + all the controls). The problem for me was the split function: the HX-3 keyboard split function works fine if you have 61 keys in a C to C arrangement (like a Nord or Novation 61), but it doesn't really handle keys outside the 61 key range if you're trying to use the split function on a larger keyboard (like my Nord 73) -- it doesn't ignore the extra keys, but it transposes them up or down an extra octave so that your keyboard effectively looks like a 61 key controller to the HX-3. They originally thought they could fix this, but I believe that the HX-3 was designed for the standard 61 note manuals, and they just can't figure out how to elegantly handle more than that. ------------ Here's an extended note if anyone is interested: There's a valid argument about the way the HX-3 handles notes above the 61 key range. The original Hammonds had 61 keys, so synthesizing higher notes can sound unauthentic. So 'folding down' the extra notes by one octave on the top of the range is not so bad, and Galileo for example does this also. However, there's really no excuse for the way they handle the lower notes when you have a +1 octave shift on the lower split. If you press a note below the 61 note range, they do a 2 octave shift even though you only asked for 1 octave. Galileo gets this one right, as does pretty much everyone else. The only way to use these things is to have either 2 keyboards, or a single 61 note C to C controller (like a novation 61), or to have a controller that outputs a split on separate upper and lower channels. Unfortunately, the Nord Electro 2 does not output the upper and lower split on separate channels (I don't know about the later ones), so that's why you shouldn't buy an hx3 to fix up the sound of a Nord 73. Quote Link to comment Share on other sites More sharing options...
M_G Posted May 19, 2016 Share Posted May 19, 2016 This will be addressed with the next update.... From the BETA "read me": 05/05/2016 Firmware #3.925, HX3 Flash #3.9e New MIDI ScanCore #30 with 88 key support, full transpose 24 notes, upper manual split +1 and +2 octaves on lower part HX3 Remote Dropdown menu bug on Win XP fixed XB2 Kit Transpose with PERCUSSION buttons (SECOND = DOWN, THIRD = UP) when Edit Mode ON Quote Studio: Hammond XK5-XLK5, Roland Fantom 8, Prophet 5, Roland SE02, Neo Vent, HX3-Expander, Yamaha Montage M7 Live: Yamaha CP88, Hammond SKX Pro, Hammond XB2-HX3, Roland Fantom 07, Roland SA1000, Neo Vent Link to comment Share on other sites More sharing options...
bluzeplayr Posted May 20, 2016 Share Posted May 20, 2016 Thanks, I'll check out the beta on github. Quote Link to comment Share on other sites More sharing options...
Bill R Adams Posted May 20, 2016 Share Posted May 20, 2016 Again. Anyone using a Native Instruments B4D drawbar controller with their HX3? Thanks in advance. Quote "You better get outta town before your nickname expires" WZ Link to comment Share on other sites More sharing options...
Doerfler Posted May 20, 2016 Share Posted May 20, 2016 hey Bill, if you don't have any luck here maybe you should try the forum over at keyboard partners. I don't go there myself but have heard good things about it. Quote Link to comment Share on other sites More sharing options...
Bill R Adams Posted May 21, 2016 Share Posted May 21, 2016 Thanks Dave Quote "You better get outta town before your nickname expires" WZ Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.